ٍAward a master's degree to Aya Nahed
The Department of Materials Engineering at the University of Technology awarded a master’s degree to the student Aya Nahed Mohsen, Department of Materials Engineering/ University of Technology, for her tagged thesis (Advanced coating to make low carbon steel suitable for many industrial applications)
The discussion was held on the discussions hall / building B / Department of Materials Engineering / University of Technology on Monday (08/11/2021). The discussion committee was formed of the teaching staff listed:
Names |
Position in the Committee
|
Prof. Dr. . Rana Afif Majeed |
Chief |
Assist. Prof. Dr. Abdul Rahman Najm |
Member |
Lec. Dr. Hind Basil Ali |
Member |
Chief researcher Dr. Hussain Muhammad Yusuf |
Supervisor |
Lec. Dr. Sura Salem Ahmed |
Supervisor |
The dissertation was scientifically evaluated by Prof. Dr. Abdul Rahim Kazem Abdul Ali / University of Babylon / Faculty of Materials Engineering, and Asist. Prof. Dr. Khaled Hamid Rashid/ University of Technology/ College of Materials Engineering/ Department of Chemical Engineering and linguistically by Lec. Dr. Sondos Karim Juma/ University of Technology/ Electrochemical Engineering Department.
Abstract
The study aimed to enhance corrosion properties for low carbon steel surface by using flame thermal spraying technique to deposit a Ni-Cu (Monel) protective coating overlay. The optimum coating parameters were (125 mm (level 2) spray distance, 30 g (level 3) N10 powder rate, substrate surface roughness, 50 mm/min (level 2) gun carrier transverse velocity). The results of SEM show the coating layer is rich in Ni-Cu, which makes it more resistant to corrosion. XRD showed the Cu and Ni-Cu phases. The erosion rate was measured by using 3.5% NaCl solution showed the minimum weight loss (0.00166 mm/year).
The discussion of the dissertation was conducted in a scientific atmosphere and a master's degree with grade of pass was awarded to the student after the completion of all the corrections that have been decided by the examiners.
ٍAward a master's degree to Zainab Salem
The Department of Materials Engineering at the University of Technology awarded a master’s degree to the student Zainab Salem Aziz, Department of Materials Engineering/ University of Technology, for her tagged thesis (Corrosion inhibition by plant extracts for carbon steel)
The discussion was held on the discussions hall / building B / Department of Materials Engineering / University of Technology on Sunday (07/11/2021). The discussion committee was formed of the teaching staff listed:
Names |
Position in the Committee
|
Prof. Dr. Anis Abdullah Kazem |
Chief |
Assist. Prof. Dr. Khaled Khudair Abbas |
Member |
Lec. Dr. Shaima Mahdi Saleh |
Member |
Prof. Dr. Rana Afif Majeed |
Supervisor |
Assist. Prof. Majed Hamid Abdul Majeed |
Supervisor |
The dissertation was scientifically evaluated by Prof. Dr. Owham Mohamed Hamid/ University of Technology / Applied science department, and linguistically by Lec. Dr. Nassier Abdul-Hussain Nassir/ University of Technology / Department of Materials Engineering.
Abstract
In this study, plant extract (wild clary) are tested and applied to steel (AISI l015) to prevent its corrosion in two mediums of sea water and 0.5 M HCl using electrochemical studies at three temperatures (298, 318, 338 K) by adding five concentrations of the extract (5, 10, 15, 20, 25) mL /L. The inhibition efficiency was found to be excellent, reaching 83.078% at a concentration of 20 (ml/L) and a temperature of 298 (K), which is the best concentration in seawater, and 92.944% at a concentration of 25 (ml/L) and a temperature of 298 (K) which is the best concentration in an acid medium hydrochloric.
The discussion of the dissertation was conducted in a scientific atmosphere and a master's degree with grade of pass was awarded to the student after the completion of all the corrections that have been decided by the examiners.
ٍAward a master's degree to Abdul Rahman Kamel
The Department of Materials Engineering at the University of Technology awarded a master’s degree to Abdul Rahman Kamel Abdul Rahim, Department of Materials Engineering/ University of Technology, for his tagged dissertation (Using recycling waste materials for preparing Eco-concrete)
The discussion was held on the discussions hall / building C / Department of Materials Engineering / University of Technology on Sunday (14/11/2021). The discussion committee was formed of the teaching staff listed:
Names |
Position in the Committee |
Prof. Dr. Alaa Aladdin Abdel Hamid |
Chief |
Assist. Prof. Dr. Sarmad Emad Ibrahim |
Member |
Assist. Prof. Dr. Ayman Jamil Kazem |
Member |
Assist. Prof. Dr. Nahed Mahmoud Ali |
Supervisor |
Lec. Dr. Ahmed Hussein Ali |
Supervisor |
The dissertation was scientifically evaluated by Lec. Dr. Raed Kazem Muhammad/Al-Mustansiriya University/College of Engineering/Department of Materials Engineering, and Assist. Prof. Dr. Ali Attia Jabr/ University of Technology/ Civil Engineering Department and linguistically by Lec. Dr. Zainab Nayef Rashid/ University of Technology/ Department of Applied Sciences.
Abstract
The aim of this study is to evaluate the possibility of using waste rubber tires as a substitute for sand and gravel. The physical and mechanical properties of rubber concrete have been tested for various sizes of rubber chopped by proportions different, so the properties that rubber concrete can gain by using this alternative are low cost, lightweight, toughness, shock absorption, and heat insulation, and preserving the environment by providing a safe solution.
The discussion of the dissertation was conducted in a scientific atmosphere and a master's degree with grade of pass was awarded to the student after the completion of all the corrections that have been decided by the examiners.
ٍAward a master's degree to Mohamed Hamed
The Department of Materials Engineering at the University of Technology awarded a master’s degree to Mohamed Hamed Maseikh, Department of Materials Engineering/ University of Technology, for his tagged dissertation (Studying the Development of Erosion Resistance of Al- Cu Alloy by Surface Treatments)
The discussion was held on the discussions hall / building C / Department of Materials Engineering / University of Technology on Monday (15/11/2021). The discussion committee was formed of the teaching staff listed:
Names |
Position in the Committee |
Assist. Prof. Dr. Fadel Abbas Hashem |
Chief |
Assist. Prof. Dr. Najeeb Salman Abtan |
Member |
Assist. Prof. Dr. Ahmed Amid Zine El Abidine |
Member |
Prof. Dr. Ali Hussein Attiwi |
Supervisor |
Assist. Prof. Dr. Jamal Jalal Daoud |
Supervisor |
The dissertation was scientifically evaluated by Assist. Prof. Dr. Bahaa Sami Mahdi/ University of Technology / Production and Minerals Department, and Prof. Dr. Kazem Kamel Rassan / Al-Mustansiriya University/ College of Engineering/ Department of Materials Engineering and linguistically by Assist. Prof. Dr. Mayada Rahim Issa/ University of Technology/ English Language Center.
Abstract
The main objective of this research is to acquire high tribological surface properties by improving the hardness and erosion resistance of alloy 2024, and to study the effect of heat and surface treatments on the hardness and erosion properties. Several heat and surface treatments were applied. These treatments are annealing, solution and aging treatment, plasma nitriding, and duplex surface treatment, which includes plasma sputtering followed by plasma nitridation. The microstructure, hardness and mechanical wear resistance of this alloy were checked before and after each treatment. An erosion tester was manufactured locally to measure the wear resistance of this alloy. X-ray diffraction, scanning electron microscopy, and Vickers hardness were used to characterize the results. The results showed that each treatment differently affects the microstructure, wear resistance and hardness of this alloy.
The discussion of the dissertation was conducted in a scientific atmosphere and a master's degree with grade of pass was awarded to the student after the completion of all the corrections that have been decided by the examiners.
Particupation in Scientific Conference
A Facility Member from The Department of Materials Engineering participates in the membership of The Preparatory Committee for the Third and First International Scientific Conference on Desertification Studies , Asst. Prof. Muhammad Abdul-Hussein Al-Zuhairi, an Faclilty Staff in the Department of Materials Engineering at University of Technology-Iraq as a member of the Preparatory Committee for the Third Scientific and First International Conference for Desert Studies in which was Held at the University of Anbar with cooperation with the Desert Studies Center for the days 17th and 18th of November
The conference included 114 research participants from Iraq, Tunisia, Kuwait, Egypt and the Netherlands, which address the problem of desertification that Iraq and the countries of the region suffer from, with the absence of strategic projects to combat desertification. Known that Asst. Prof .Dr Mohammed Al-Zuhairi is an observer member of the United Nations Convention to Combat Desertification (UNCCD) and an accredited member of the United Nations Environment Program (UNEP).