اخبار القسم en
Students of the first stage, begun performing the finally exams of the first course of (2017-2018) academic year, in 11/2/2018. Assist Prof. Dr. Ahmed Mohammed Hasan,the dean of college,followed up the exams personally, to ensure of providing all necessary requirements to perform exams inside halls.
On 10/1/2018 2018 a seminar presented by Asst.Prof Dr. Mohamed Abdel-Hussein Mohamed Faculty staff at the Materials Engineering Department / University of Technology to participate in the TMREES Conference Series, to be held in early February in Beirut, Lebanon. (The use of the bubble column reactor and the CFD simulation for the polyethylene recycling of polyethylene terephthalate) was discussed. The research dealt with the use of the bubble column reactor and the natalite catalysis technology in the dismantling of polymerization of plastic water bottles and the production of polyethylene terephthalate monomer and its use in improving asphalt as a coating of concrete to increase mechanical and thermal resistance and cohesion Reduce water absorption.
On 22/1/2018 a Seminar was presented by Wafa Mahdi Saleh Teaching at the Materials Engineering Department / University of Technology Semner Scientific in order to participate in the scientific conference marked: (TMRESS Confrence Series) to be held in early February in Beirut - Lebanon. The study dealt with the effect of some mechanical properties of an overlapping material (polyester supported by various natural fibers - palm fiber, natural fiber, cecil plant and cannabis plant) and then treated I am chemically treated with NaOH by 10% and then comparing the results to the overlapping material with and without the chemical treatment of the fiber.
On 25/1/2018, the graduate student (master) Sara Abdel-Salam Hattab had discussed her thesis:(Polymer coating connector to reduce the risk of corrosion)The discussion committee consisted of the listed gentlemen
- Asst.Prof.Emad Saadi Abdulkareem University of technology\Department of Materials Engineering Head of committee
- Asst.Prof. Bissam Ibrahim Khalil University of technology\Department of Materials Engineering. Member
- Dr. Hussein Mohammed Yosef Ministry of Industry and Metals \ Member
- Prof. Rana Afif Anani University of technology\Department of Materials Engineering Supervisor
- Asst.Prof. Waf’a Mahdi Saleh University of technology\Department of Materials Engineering Supervisor
The thesis addressed the possibility of using both the inhibitors with the coating to obtain a thin and homogeneous coating layer of the non-pyrolymol polymer and with the amalgamation of organic and inorganic amines on carbon steel (St 44-2-DIN 17100) by electrochemical polymerization of the pyrolymol monomer and the possibility of improving corrosion resistance in the water medium Saline (3.5% sodium chloride) at different temperatures (293, 303, 313, 323 and 333)Kelvin. was studied,the structure and morphology of polymerized pyrolyle strata was studied using electron microscopy (SEM), AFM, FTIR spectroscopy and adhesion examination.
Scanning electron microscopy images showed the structure and morphology of the polypearol layer deposited on carbon steel. In general, the distribution of pyrolytes and saplings covers the surface on a regular basis. The variation of surface morphology is due to the composition of the cauliflower. While the images of the atomic force microscope showed the best growth of polypirol fibers, the morphology and roughness of the surface were also estimated from the atomic force microscope examination. Polysaccharides in organic anions cause little change in surface morphology. The polysaccharide polycrystalline polysaccharide is indicated
he results obtained from this study were shown by different corrosion-labeling techniques for carbon steels indicating the proposed insoluble polyol polyol for use as a conductive polymer and for optimal protection against erosion in seawater (3.5% NaCl solution). Prompt in industrial application, environmentally friendly and chemically stable
The thesis was evaluated scientifically by Prof. Dr.Awda Jabbar Breehi / University of Babylon / Faculty of Engineering and linguistics by AMD. Samir Ali Amin / University of Technology / Department of Mechanical Engineering.
The discussion was held at the Graduate Hall / Building C and the discussion committee was granted a Master's degree for the student.
On 24/1/2018 the graduate student (Masters) Russul Salah Hadi discussed entitled her thesis entitled:
(Use of auxiliary materials in the chemical recycling of waste water bottles and their use in industrial applications)
The discussion committee consisted of the listed gentlemen
- Asst.Prof. Kadhem Mutter Shebeb Univesity of technology\Department of Materials Engineering Head of committee
- Asst.Prof, Saad Hanash Ammar University of Nahrain College of engineering. Member
- Asst.Prof. Mohammed Ramaid Gharkan Univesity of technology\Department of Materials Engineering Member
- Asst.Prof. Bissam Ibrahim Khalil Univesity of technology\Department of Materials Engineering Supervisor
- Asst.Prof. Kadhem Mohamed Abdul Hussein Univesity of technology\Department of Materials Engineering Supervisor
The study examined how mono meres were manufactured by recycling plastic water bottles using auxiliary materials using zinc oxide in two types (94.55) and with different weights (0.5,0.25,0.15 g) and using two types of nano-magnesium oxide and effective thinner with different weight ratios The use of a closed glass system at 190 ° C and the study of the effect of the ratio of the catalyst, the reaction time and the yield of the resulting material, and the analysis of the elements (carbon, hydrogen and nitrogen) ,The results showed that zinc oxide (55) was more productive and effective than the zinc oxide nanotubes (94) due to the large surface area of the nanotube zinc oxide (55) and reduced the reaction time to one hour instead of (7) hours and without the use of auxiliary materials using a simple closed system and economic costs
The thesis was evaluated scientifically by Prof.D.Kazem Kamel Rassen / University of Mustansiriya / Faculty of Engineering and linguistics by Prof. Dr. Akhtar Khallakal Hussein / University of Technology / Department of Mechanical Engineering.
The discussion was held at the Graduate Hall / Building C and the discussion committee was granted a Master's degree for the student.
Scientific seminars
On 8/1/2018, a group of teachers of the Materials Engineering Department / University of Technology has been working on scientific research to participate in the Tmress Confrence Series, to be held in early February in Beirut, Lebanon. The title of the first research presented by Asst.Prof.Dr. Ala’a Alla al-Din (Characteristics of Thin Films of SnO2 Deposited by Thermal Chemical Spraying Using Different Salt Solutions). In this Paper, the thermal chemical spraying method was used with one atomizer and two nozzle (SN, DN). The thin tin oxide membranes were formed in different structures. The tin oxide membranes were prepared at a concentration of 0.005M and their thickness was about 0.2 - 0.002 μm. Microscopic examination of the membranes, in addition to optical transparency and to the contact angle. The results showed that the membranes were crystallized with a four-angular structure with tiny micro-structures from plates to columns and clusters resembling cast.
The second research presented by Asst.Prof.Assel Basem (Natural fiber recycling and use in green cement mortar) to the process of manufacturing environmentally friendly cement mortar consisting of natural waste (coconut fiber, banana fiber, papyrus fiber, and palm fiber). Various additives (0 - 0.25 - 0.50-0.75-1 g) Natural waste (plant fiber) was the partial replacement of cement, mechanical properties and thermal conductivity. It was found that the increase of additives from natural waste increases the strength of the pressure and the hardness of cement mortar and the lack of thermal conductivity properties and water absorption. a To take advantage of these wastes and recycling instead of burning them.
Author of a scientific book
Al-Yamamah , Publishing and Distribution published a scientific book entitled "Transformations in Engineering Materials".Prof.Dr. Abbas Khamas Hussain Teaching in Materials Engineering / University of Technology. The third chapter deals with the process of synthesis. The fourth chapter focuses on the process of growth. Chapter 5 deals with the applications of transitions and ends with Chapter 6, which included a set of questions and questions.
Acknowledgments
- On 28/12/2017, the Head of Materials Engineering Department / Ahmed Mohamed Hassan Al-Ghabban on the book of thanks number 63 on 2/1/2018 by the President of the University of Technology Amin Douai Thamer Tomena for the efforts made and distinguished in the success of the specialized symposium tagged (Instructions for new scientific promotions No. 167 of 2017)
- On 19/12/2017 Prof. Dr.. Ali Hussein Ateey Teaching in the Department of Materials Engineering / University of Technology on the book of thanks and appreciation number 6656 on 19/12/2017 by Asst.Prof.Dr . Mohammed Said Abdul-Zahra, Dean of the Faculty of Medicine / University of Kufa in recognition of his great efforts and support to the Faculty of Medicine in the forums of the Council of the University of Kufa and his guidance in changing the curriculum and wish him success and success.
- On December 28, 2017, Asst.Prof Laith Qais Abbas rescived Aknowledgement number 67 on 2/1/2018 by the President of the University of Technology Amin Douai Thamer for the efforts made and distinguished in the success of the specialized symposium tagged (Instructions for new scientific promotions No. 167 of 2017.
Scientific promotion
On 4/1/2018 and in implementation of what was stated in the meeting of the fourth session of the Committee of the university for scientific promotion held on 20/11/2017 for the academic year 2017-2018 and associated with the approval of the President of the University of Technology. Amin Douai Thamer and the approval of the Council of the University in its fourth session held on 20/11/2017 and according to the letter of the Secretariat of the Council of the University No. MG / 1/1593 on 27/12/2017 decided to promote the Asst.prof.Dr. Abbas Khamas Hussain Teaching in the Department of Materials Engineering / University of Technology from the rank of assistant professor to the rank of professor.
First course exams
On 9/1/2018, the students of the preliminary study in Materials Engineering / University of Technology began the exams for the end of the first course for the academic year 2017-2018. Where the President of the University of Technology. Prof. Dr. Amin Douai Thamer visit inspection to see the progress of examinations within the examination halls and to make some inquiries from students for the purpose of reassuring the progress of the examination process as well as directing some instructions for the performance of examinations, which are aimed at the successful conduct of the examination process.
Voluntary work
- On 13/12/2017 participated Materials Engineering Department / University of Technology and under the guidance of the Committee of Educational Guidance, Dr. Sihama Issa Saleh volunteered to visit the graduate students (Masters) / stage of the courses to Dar Al-Alawia for orphans as well as nursing home / Rashad to provide assistance and moral support for these age groups and to encourage students to Voluntary work that serves the community as part of the message The section represented by the formation of a consciously educated generation that serves his country in all fields of science and humanity.
- On 4/1/2018 students from the Department of Materials Engineering / University of Technology:
1- Karam Thamer (fourth class/ General Materials)
2- Alia Abbas Ali (third class / ceramics)
3 - Aya Mazen Qassem (Second class)
As part of the Volunteer Voluntary Campaign, visit the Children's Hospital of Central Education / Housing to help the children of cancer patients and help them through the distribution of gifts and donations as well as providing moral support to them and encourage them to fight the disease and continue life and wish them speedy recovery.
More...
Participation in a symposium
On 7/1/2018 Participated in the Department of Materials Engineering / University of Technology in the third quality symposium held in the Department of Production Engineering and Minerals / University of Technology and tagged:
(The central symposium for the development of laboratory testing devices and its role in raising standards of quality and laboratory accreditation)
(TEM, SEM, OM), the mechanism of work of each device with details of its work and the clarification of the urgent need to show the details of the engineering samples of different types of materials, whether ceramic, polymeric or metal, to produce comprehensive scientific results serving Scientific research and keep abreast of global development.
Acknowledgments
On 14/12/2017, the President of the University of Kufa / Mohsen Abdul Hussain Al-Dhlami A book of thanks and appreciation number no. / 807 dated 17/12/2017 to Prof. Ali Hussein Atewi Teaching Materials Engineering Department / University of Technology. In appreciation of the continuous effort and effort during the tenure of Dean of the Faculty of Engineering / University of Kufa, wishing him success.
Faculity Staff Meeting
On 21/11/2017 a meeting of a Faculty Staff was held for faculty members in the Materials Engineering Department / University of Technology for the purpose of clarifying the project of the independence of the university of technology. The meeting included an explanation of the subject of independence in all its scientific and administrative aspects. Ahmed Mohamed Hasan Al-Ghaban to the possibility of access to the teachers of all the provisions of the Ministerial Order issued in this regard and answer all queries related to the subject in this regard as additional sessions will be held for the purpose of consultation.
The meeting also touched on some important issues related to admission of students for this year and the tuition fees for the first semester of the academic year, and some important directives relating to the morning and evening studies were mentioned.
Chinese delegation Visit
On November 21, 2017, a Chinese delegation accompanied by the Director of the Rehabilitation and Employment Division, Mr. Ammar Musa, visited the Materials Engineering Department at the University of Technology and was received by the Head of Laboratories. Jamal Jalal, where he briefed the delegation on the mechanism of work laboratories and the possibility of developing a mechanism of cooperation with the Department and the extent of possibilities available by the Department
